Hunter Xcore Sprinkler Manual

Hunter Xcore 사용 설명서

In this 'How To' video, our Smart Water Shop Operations Manager - Matthew Bristowe - shows us how to factory reset a Hunter X-Core Irrigation Controller. Th.

Como programar controlador xcore hunter YouTube

Use the PRG button to select program (A, B, or C). 3. Use the + and - buttons to change the Start Time. The Start Time advances in 15-minute increments. 4. Press the button to add another Start Time, or PRG button to set a Start Time for the next program. 5. Turn the dial to the RUN position. ELIMINATING A PROGRAM START TIME 1.

Hunter XCore 8 Station Controller Indoor The Watershed Water Systems OFFICIAL WEBSITE

Resetting X-Core. Press and hold down the , and buttons simultaneously. Press and release the RESET button on the right side of the controller. When DONE appears on the LCD, release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed. Reset procedure for the Hunter X.

How to adjust irrigation Hunter XCore controller YouTube

If you have an X Core controller that seems to be playing up then the most likely cause is that it needs resetting. This can be done easily. 1. Press and hold the 'PROG' button. 2. While holding the 'PROG' button press the RESET button for 3 seconds, then release the RESET button while continuing to hold the 'PROG' button. 3.

Hunter XCore computer PVC24.nl

Maximum Solenoids per Output. Welcome to the X-Core irrigation controller support section. The X-Core, which is the XC timer predecessor, is Hunter's professional controller for 2 to 8 zones. This section will show you how to install, program and troubleshoot your X-Core controller.

hunter x core quick check and reset features Manualzz

Attach the two yellow wires to the AC terminals. receiver to the wall next to the irrigation 2. Page 322 The reCeiver Wiring the receiver to a hunter X-Core, pro-C, Wiring the receiver to a hunter aCC iCC and i-Core 1. Connect the blue and white wire to any of the four Sensor Terminal pairs (Sen 1 shown). 1.

Hunter XCore Residential Indoor Controller Sierra Irrigation

HUNTER X CORE TROUBLESHOOTING GUIDE PROBLEMS . The Controller is continually watering . CAUSES . Too many start times have been programmed .. Press and release the RESET button on the back of the front panel. Wait until the display shows 12:00am. Release the may now be reprogrammed. button. All the memory has been cleared and the controller.

how to program hunter X core controller YouTube

Press and release the RESET button in the lower wiring compartment. Release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed. X-Core. Press and hold down the , and buttons. Press and release the RESET button on the right side of the controller.

Hunter XCore401iE Amazon.es Bricolaje y herramientas

The Hunter X-Core has long been the benchmark for irrigation controllers. With a number of programming options, it's versatile, and can be programmed to suit.

Hunter X Core Sprinkler Controller

If want to clear the memory on your controller and start from fresh or if your controller is not responding to your commands, this video will show you how to.

Reset a Hunter XCore irrigation controller YouTube

X-Core - Reset / Clearing the Controllers Memory. Reset a Hunter Controller - Quick Tip. Watch on. Press and hold the button. While holding the button, press the RESET button for 3 seconds then release while continuing to hold the button. Continue holding the button until the display shows 12:00am or "DONE".

Irrigation Walk through Hunter XCore Controller YouTube

1 X-Core Components. 2 Setup. 2.1 SETTING THE CURRENT DATE AND TIME. 2.2 SETTING A PROGRAM START TIME. 2.3 ELIMINATING A PROGRAM START TIME. 2.4 SETTING A STATION RUN TIME. 2.5 SETTING WATER DAYS. 2.6 SELECTING ODD OR EVEN DAYS TO WATER. 2.7 SELECTING INTERVAL WATERING.

Hunter XCore Irrigation Controller

A controller can sometimes experience a "glitch" if it has received a power surge or other electrical anomalies. Your controller may not be damaged, however, it may require resetting. A successful reset will result in a 12:00 am on the display. Here is the reset procedure for the Hunter X-Core Controller:

Hunter Xcore Sprinkler Manual

Solution. RED (AC1), WHITE (AC2) and BLUE (REM terminal) Check the master valve or pump start wire for continuity. Replace or repair the shorted wire. Check that all wire connections are good and watertight. Check electrical specifications for pump relay - Do not exceed controller's electrical rating. Replace defective pump relay or solenoid.

Hunter XCore Programming Overview and Setting Up Program A YouTube

To reset a Hunter x Core irrigation controller to its factory default settings, follow these steps: Turn off the power to the controller by unplugging it or switching off the circuit breaker. Locate the small reset button on the back of the controller. Using a paperclip or similar object, press and hold the reset button for at least 5 seconds.

Controlador Hunter XCore 2 estações Interno Casairriga

Page 5 Use to attach transformer, sensor, and valve wires from their source to the controller Reset Button Use to reset the controller. CONNECTING A HUNTER SOLAR SYNC ET SENSOR The X-Core is compatible with the Solar Sync and Wireless Solar and the default Water Adjustment setting (5) on the right. Adjust Sync systems.